datasheet | december 2013 fiber optics | rev 2013.12 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. applications high-performance supertrunking links optical distribution networks redundant ring architectures fttx networks. features full functionality 1 ru edfa (pre-amp) low noise figure (typ < 3.3 db) total input power range: -45 dbm to 0 dbm +14 dbm saturated output power (min) small signal gain 37 db (min) standard rs-232 communications (rs-485 or i 2 c is optional) key lock switch vfd panel status indicator low electrical power consumption output isolation >40 db polarization dependant gain < 0.1 db polarization mode dispersion < 0.5 ps the emcore pona 2114 pa series erbium doped fiber pre-amplifier (edfa) is an ideal building block for oem system integrators. the family of pona 2114 pa series preamps is designed to meet the most demanding noise performance requirements of any fiber link applicatio n, and perform all the functions required of an optical pre-amplifier for system integration. the pona 2114 pa series provides optical isolation on the output of the gain block for stable, low noise operation. the output optical signal power levels are detected for monitoring and control. the pona 2114 pa series also provides monitors and associated alarms for all vital characteristics. the relay outputs of the pona 2114 pa series provide electrical monitoring of alarm conditioning of the unit. general and mechanical specifications property requirement comments operating wavelength 1530 ? 1562 nm standard operating case temperature 0 ? c to 50 ? c storage temperature -40 ? c to 85 ? c standard operating humidity 20% to 85% non-condensing voltage supply range 85 vac to 265 vac 50/60 hz -36 to -60 v dc standard optional optical connectors sc/apc; sc/upc; fc/apc; fc/upc; e2000/apc user specified dimensions in inches 19.0?w x 14.76 ?d x 1.72?h 19? rack-mounted, 1u pona 2114 pa series edf a erbium doped fiber pre-amplifier
datasheet | december 2013 fiber optics | rev 2013.12 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. optical/electrical characteristics 1 property symbol (units) limit specifications comments operating input power pin (dbm) max 0 operating input power pin (dbm) min -45 saturated output power po (dbm) 14 minimum (note 2) operating wavelength range nm min/max 1530 ? 1562 nominal noise figure nf (db) max 3.3 (note 3) power consumption psys (w) max 6 +50c case notes: 1. unless stated otherwise, all specif ications apply over the full operating temperature and humidity ranges. 2. measured @ 1550 nm, pin -4 dbm and @ 25c. 3. measured @ 1550 nm, pin -30 dbm and @ 25c. outline drawing ac versions shown below with 8-port option dc versions shown below with 8-port option pona 2114 pa series edf a erbium doped fiber pre-amplifier
datasheet | december 2013 fiber optics | rev 2013.12 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. compliance information 89/336/eec electromagnetic compatibility directive, amended by 92/31/eec & 93/68/eec 73/23/eec low voltage dire ctive, amended by 93/68/eec en 50083-2, (2001) cable networks for tv signal s, sounds and interactive services, part 2 electromagnetic compatibility for equipment. en 55013 mains conducted emissions en 61000-3-2 mains freq uency and its harmonics, conducted emissions en 55020 radiation from active equipment, radiated immunity en 61000-4-6 immunity of active equipment, radiated immunity en 61000-4-3 immunity of active equipment, radiated immunity en 61000-4-2 electrostatic discharge immunity en 61000-4-4 electr ical fast transient / burst immunity en 60950 low voltage directives en 60825-1 laser safety requirement en 60825-2 laser safety requirement cdrh laser safety requirement fit rate: 90% level of confidence < 1700 @ 30 ? c (pona 2130) ordering information pona 2114 - 1 - - - pa laser safety information this product meets the applicable requirements of 21 cfr 1010 & 1040 and is classified as a class iv laser product based on the maximum optical output power shown below. during use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiati on and would meet the requirements for a class i laser product. the laser product report has been submitted to the cdrh and the accession number is expected by october 2006. wavelength = 1530 ~ 1562 nm (dependant on input source) maximum output power = 30 mw (single output) input voltage connector type ac ? 90-260v 50/60 hz sc ? sc/apc dc ? 48 v fc - fc/apc ec ? e2000/apc tc ? sc/upc gc ? fc/upc pona 2114 pa series edf a erbium do p ed fiber p re-am p lifier
|
